Filename: ///sbin//update-secureboot-policy

#!/bin/sh
set -e

if  test $# = 0                                                 \
    && test x"$SHIM_NOTRIGGER" = x                              \
 && test x"$DPKG_MAINTSCRIPT_PACKAGE" != x                      \
 && dpkg-trigger --check-supported 2>/dev/null
then
        if dpkg-trigger --no-await shim-secureboot-policy; then
                if test x"$SHIM_TRIGGER_DEBUG" != x; then
                        echo "shim: wrapper deferring policy update (trigger activated)"
                fi
                exit 0
        fi
fi

. /usr/share/debconf/confmodule

setup_mok_validation()
{
    local moksbstatert
    local efivars secureboot_var moksb_var moksbstatert_var
    local enable_sb action
    enable_sb=$1
    efivars=/sys/firmware/efi/efivars
    secureboot_var=SecureBoot-8be4df61-93ca-11d2-aa0d-00e098032b8c
    moksb_var=MokSB-605dab50-e046-4300-abb6-3dd810dd8b23
    moksbstatert_var=MokSBStateRT-605dab50-e046-4300-abb6-3dd810dd8b23
    action=disable

    if [ $enable_sb -eq 1 ]; then
        action=enable
    fi

    if ! [ -f $efivars/$secureboot_var ] \
       || [ "$(od -An -t u1 $efivars/$secureboot_var | awk '{ print $NF }')" -ne 1 ]
    then
        echo "Secure Boot not enabled on this system." >&2
        return 0
    fi
    moksbstatert=0
    if [ -f $efivars/$moksb_var ]; then
        # if MokSB exists we've likely already run mokutil since last boot
        echo "The Secure Boot policy was already changed since last reboot; nothing to do." >&2
        return 0
    fi
    if [ -f /proc/sys/kernel/moksbstate_disabled ]; then
        moksbstatert=$(cat /proc/sys/kernel/moksbstate_disabled 2>/dev/null || echo 0)
    elif [ -f $efivars/$moksbstatert_var ]; then
        # MokSBStateRT set to 1 means validation is disabled
        moksbstatert=$(od -An -t u1 $efivars/$moksbstatert_var | \
                       awk '{ print $NF; }')
    fi
    # poor man's xor
    if [ $(($moksbstatert+$enable_sb)) -ne 1 ]; then
        STATE=1
        db_settitle shim/title/secureboot
        while true; do
            case "$STATE" in
            1)
                db_capb
                db_fset shim/secureboot_explanation seen false
                db_input critical shim/secureboot_explanation || true
                db_go

                # Allow the user to skip disabling Secure Boot.
                db_fset shim/${action}_secureboot seen false
                db_input critical shim/${action}_secureboot || true
                ;;
            2)
                db_get shim/${action}_secureboot
                if [ "$RET" = "false" ]; then
                    break
                fi

                db_input critical shim/secureboot_key || true
                seen_key=$RET
                db_input critical shim/secureboot_key_again || true
                ;;
            3)
                db_get shim/secureboot_key
                key="$RET"
                db_get shim/secureboot_key_again
                again="$RET"

                if [ -z "$key$again" ] && echo "$seen_key" | grep -q ^30; then
                    echo "Running in non-interactive mode, doing nothing." >&2
                    exit 1
                fi

                db_capb
                if [ "$key" != "$again" ]; then
                    db_fset shim/error/secureboot_key_mismatch seen false
                    db_input critical shim/error/secureboot_key_mismatch || true
                    STATE=$(($STATE - 2))
                else
                    length=$((`echo "$key" | wc -c` - 1))
                    if [ $length -lt 8 ] || [ $length -gt 16 ]; then
                        db_fset shim/error/bad_secureboot_key seen false
                        db_input critical shim/error/bad_secureboot_key || true
                        STATE=$(($STATE - 2))
                    elif [ $length -ne 0 ]; then
                        printf '%s\n%s\n' "$key" "$again" | mokutil --${action}-validation >/dev/null || true
                    fi
                fi

                # Always clear secureboot key.
                db_set shim/secureboot_key ''
                db_fset shim/secureboot_key seen false
                db_set shim/secureboot_key_again ''
                db_fset shim/secureboot_key_again seen false
                ;;
            *)
                break
                ;;
            esac

            if db_go; then
                STATE=$(($STATE + 1))
            else
                STATE=$(($STATE - 1))
            fi
            db_capb backup
        done
        db_capb
    fi
}

args=$@
enable_secureboot=0

if echo "$args" | grep -qc -- '--enable'; then
	enable_secureboot=1
elif echo "$args" | grep -qc -- '--disable'; then
	enable_secureboot=0
elif echo "$args" | grep -qc -- '--help'; then
	echo "update-secureboot-policy: toggle UEFI Secure Boot in shim"
	echo
	echo "\t--enable\tPrompt to enable Secure Boot validation."
	echo "\t--disable\tPrompt to disable Secure Boot validation (default)."
	echo "\t--help\t\tThis help text."
	exit 0
fi

if [ -d /var/lib/dkms ] &&
       [ `find /var/lib/dkms -type d -print | wc -l ` -gt 1 ]; then
    setup_mok_validation $enable_secureboot
else
	echo "No DKMS packages installed: not changing Secure Boot validation state."
fi

exit 0

./Ninja\.